- 您现在的位置：买卖IC网 > Sheet目录19082 > 91350-1 (TE Connectivity)SEATING TOOL HMZD RCPT 2 PAIR
Seating Tools 91347- [ ], 91350- [ ], and 91376- [ ]
Electric Servo Presses (BMEP 3T) 1585697--1, and
(BMEP 5T) 1585696--1 are available for this seating
tool. For information on the presses, visit the press--fit
assembly equipment website at
http://tooling.tycoelectronics.com/pressfit.asp .
408- 8500
5. Center the seating tool (with the connector)
under the ram of the applicator tool; slowly lower
the ram until it just meets the seating tool. Verify
the alignment of the pc board support fixture, pc
board, connector, and seating tool.
CAUTION
!
4. SEATING
Over--driving of the connector will deform parts
critical to the quality of the connection. Maximum
force occurs prior to the connector bottoming on
the pc board.
CAUTION
!
Damage to the pc board, seating tool, or
connector may occur if the seating height is
improperly set, the pc board is not properly
positioned over the pc board support, or the
seating tool is not properly seated on the
connector before cycling the applicator ram.
i
1. Set seating height to the dimension shown in
Figure 2 (application tool shut height will equal the
tool seating height PLUS the combined
thicknesses of the pc board and support fixture).
After seating, a gap of no more than 0.10 mm
[.004 in.] between the connector housing and the
pc board is allowed.
NOTE The seating height of 38.1 mm [1.50 in.] is a
reference starting point. The seating height might
have to be adjusted to properly seat the
connector onto the pc board.
2. Position the connector on the pc board so that
contacts are properly aligned with the holes in the
pc board and pc board support fixture.
3. Sit the connector onto pc board until the open
section of the contacts are resting securely on, but
have not fully entered, the holes in the pc board.
4. Position the seating tool onto the connector.
6. Cycle the ram according to instructions included
with the application tooling. Check the connector
for proper seating using the requirements in
Application Specification 114--13059.
7. Remove the pc board or re--position the pc
board and pc board support fixture for seating
additional connectors.
5. MAINTENANCE AND INSPECTION
5.1. Daily Maintenance
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or lint--free cloth. DO NOT
use objects that could damage the tool or any of its
components.
Note: Not to Scale
View After Seating
Applicator Ram
(Fully Down)
Seating Height
(Connector Seated)
38.1 [1.50] Ref
Seating Tool Centered Under
Applicator Ram and
Bottomed on Connector
Applicator Tooling
Shut Height
(Ram Down)
Maximum Gap
Allowed
0.10 mm [.004 in.]
Contacts in PC Board Holes and Aligned
with Holes in PC Board Support Fixture
PC Board
PC Board Support Fixture
Figure 2
2 of 4
Tyco Electronics Corporation
Rev F
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
GW5DLA50M04
LED MOD 15WATT ZENIGATA 5000K
HR22-12P-T01
TOOL WIRING JIG FOR HR22
A0153B
SWITCH BLOCK FOUR POLE
P51-500-S-I-P-5V-000-000
SENSOR 500PSIS 7/16 UNF 5V
P51-300-S-I-P-5V-000-000
SENSOR 300PSIS 7/16 UNF 5V
SBT-39-G-K11-MPE
BIG CHIP LED HB MODULE GREEN
P51-200-S-I-P-5V-000-000
SENSOR 200PSIS 7/16 UNF 5V
88970123
CONTROL LOGIC SERIAL CABLE 1.5M
相关代理商/技术参数
913501-003
制造商:Glenair Inc 功能描述:ADAPTER - Bulk
913501-005
制造商:Glenair Inc 功能描述:ADAPTER - Bulk
9135019321
制造商: 功能描述: 制造商:undefined 功能描述:
913502
制造商:Weidmuller 功能描述:KDKS 1/EN4 LDU; 110VAC/60VDC -EA - Bulk
91350-2
功能描述:手工工具 SEATING TL RCPT 2 PR 20 COL
RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool
91350--2
制造商:MACOM 制造商全称:Tyco Electronics 功能描述:Seating Tools 91347- [ ], 91350- [ ]
913503
制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:10.16mm (.400") Beau? Eurostyle?, Fixed Mount PCB Terminal Block, High Voltage, High Power 40A, 3 Circuits
913504
制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:10.16mm (.400") Beau? Eurostyle?, Fixed Mount PCB Terminal Block, High Voltage, High Power 40A, 4 Circuits